Elac Miracord 50 Turntable

DESCRIPTION

Elac Miracord 50 Turntable 

Smooth vinyl precision.

ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo, when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt-drive motor and die-cast aluminum platter. A precision static balanced, straight-tube tonearm with removable headshell features a factory-mounted MM phono cartridge. Designed with convenience in mind, the Miracord 50 is equipped with a built-in defeatable phono preamplifier, allowing you to add this turntable to virtually any music system.

Anti-resonant Chassis
Superior isolation is achieved with a chassis designed to minimize the sonic effects of vibration and feedback. A low-noise DC servo motor drives a die-cast, high-inertia aluminum platter with special record mat via a rubber belt, resulting in stable speed and minimal wow and flutter. 

Precision Tonearm and Cartridge
The tonearm is a static-balance, straight tube design with precision bearings, builtin anti-skate adjustment and removable bayonet-style headshell. A premounted moving-magnet cartridge takes all the guesswork out of setup and assures proper vertical tracking angle, tracking weight and azimuth adjustment right out of the box.

Built-in Phono Equalizer Amplifier
Unlike most turntables, the Miracord 50 comes complete with a built-in defeatable phono preamp for correct RIAA equalization. That means you can add LP playback without having to add a costly phono stage to line-level preamps or digital-only systems. Just plug it in, put on a record and enjoy rich LP sound! 

Contemporary Finish
Styled to complement any interior, the Miracord 50 is available with a silver chassis and gloss-black plinth. A hinged, tinted dustcover is included.

 

 

SPECIFICATIONS

Turntable Section

Drive System: Belt drive
Motor: DC motor
Selectable Speeds: 33⅓ and 45 rpm
Motor Servo: Speed rotation and servo system
Rotation Speed Variation: +/-1%
Wow and Flutter: 1%
Signal-to-Noise Ratio: -67 dB or higher (A-weighted) -60 dB or higher (unweighted)
Platter: Aluminum die-cast
Platter Diameter: 0 in / 300 mm

Tonearm Section

Type: Aluminum tube, static-balanced
Effective Arm Length: 8 in / 223.6 mm
Stylus Pressure Range: 0 to 0 g
Cartridge Weight Range: 5 to 6.0 g
Effective Arm Mass: 4 g
Overhang: 6 mm
Offset Angle: 25 degrees
Anti-Skating: Adjustment Supported
Main Bearing: Stainless steel

Cartridge Section:

Type: Audio-Technica AT91 moving magnet
Stylus Construction: Bonded diamond
Mount: Half-inch
Frequency Response: 20 Hz to 20 kHz
Channel Separation: >18 dB
Channel Balance: 5 dB
Vertical Tracking: Angle 20 degrees
Stylus Pressure: 0 g +/-0.5 g
Cartridge Weight: 0 g +/-0.5 g
Headshell Weight: 0 g (including screws, nuts and wires)

Phono Equalizer Amplifier

Type :Moving magnet (MM)
Phono Output: 5 mV (1 kHz, 3.54 cm/sec)
Line Output: 140 mV (-17 dBV)
Phono/Line: Switchable
Supported Load Impedance: 47 kΩ

Connector: RCA pin jack including RCA cable accessories
Voltage: 100 to 240 V AC / 50 to 60 Hz
Power Consumption: 1.5 W (less than 0.5 W at standby)
Dimensions: (WXHXD) 5.5 x 16.05 x 14.20
Weight: 12.10 lb