Wood feel PLA based filament EasyWood 1.75mm Pine 500 gram 3D Printer Filament
This ad is on hold, please check again later.
Wood feel PLA based filament EasyWood 1.75mm Pine 500 gram 3D Printer Filament
$62.99
SUMMARY
EasyWood is a wood-filled PLA-based filament which is gravimetrically filled with approximately 40% grinded wood...
DESCRIPTION
EasyWood is a wood-filled PLA-based filament which is gravimetrically filled with approximately 40% grinded wood particles. EasyWood is a very easy to print wood filament as it is based on our EasyFil PLA compound and the 40% gravimetrical filling with grinded wood particles make the filament absolutely warp-free.
EasyWood looks, feels and smells like real wood and beautiful wood-nerve structures can be obtained by grinding the printed object a bit with a piece of fine grit sandpaper or by varying with the printing temperature.
Unique features
Extremely high wood-filling of 40% Real wood feel, look and smell Very easy to print Warp-free printing and no deformation after cooling Great thermal stability and filament flowing behaviour Perfect first- and inter-layer adhesion Can be printed at high printing speeds Create wood-nerve structures By postprocessing the printed object with a piece of fine grit sandpaper By varying with the print/extrusion temperature Biodegradable
General printing guidelines *
Nozzle size: ⥠0.4mm
Layer height: ⥠0.2mm
Flow rate: ± 104%
Print temp: ± 210 - 240° C
Print speed:Â Low
Retraction: Yes ± 5mm
Heat bed: ± 0 - 60° C
Fan speed:Â 50-100%
Experience level:Â Beginner
*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.
Filament length
Ï: 1.20 g/cc
50 gr coil
0.5 Kg spool
2.3 Kg spool
à 1.75mm
± 17.3m
± 173m
797m
à 2.85mm
± 6.5m
± 65m
300m
Nozzle cleaning
When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.
Product export information
HS Code:Â 39169090
Description:Â Monofilament
Country of origin:Â the Netherlands
Compliance *
This filament is compliant to below listed directives and regulations.
*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.
UPC: 0.80 KGS Weight: 0.80 KGS
Brand:
Visit our website to view thousands more products like this and order online at:
ADDITIONAL INFORMATION
Price
$62.99
Condition
New
Delivers To
Australia Wide
YOU MAY ALSO LIKE
PLA Filament Silk Gloss PLA 2.85mm 750 gram Radiance Green 3D Printer Filament
Silk Gloss PLA (polylactic acid) is modified with another polymer to have a very smooth and silky surface finish with a...
$78.99
Ad is on hold
New
PLA Filament Silk Gloss PLA 1.75mm 750 gram Radiance Green 3D Printer Filament
Silk Gloss PLA (polylactic acid) is modified with another polymer to have a very smooth and silky surface finish with a...